Fuel Management

How to Maintain Stored Diesel Fuel

November 2016, Government Fleet - Feature

by James Dunst

Backup generators, which may be refueled only once or twice a year, need diesel fuel maintenance to ensure they function when needed. Photo: Shutterstock
Backup generators, which may be refueled only once or twice a year, need diesel fuel maintenance to ensure they function when needed. Photo: Shutterstock

When the Environmental Protection Agency (EPA) mandated a change to ultra-low sulfur diesel (ULSD) in 2007, it caused some significant problems for fleets. The majority of fleet managers are not aware of these problems. From fuel microbes to water contamination, here are the problems and how to prevent (or solve) them.

ULSD Problems: Lack of Lubrication and Increased Microbial Growth Rate

Prior to the introduction of ULSD, diesel fuel contained 500 parts per million (ppm) of sulfur, which had two positive effects. First, sulfur was a lubricant for seals in the fuel injectors and injector pumps. Most diesel engines built prior to the year 2000 relied heavily on this lubrication and were not made to run optimally on ULSD; its use could result in premature wear of fuel system components. 

Second, sulfur acts as a natural biocide that helps prevent microbial growth in diesel fuel tanks. This microbial growth in diesel fuel is not algae, although many people think it is. Removing the sulfur makes the fuel much less resistant to fuel microbes — fungus, mold, and bacteria — which then have to be treated with a biocide.

In 2007, the EPA mandated the switch to 15 ppm of sulfur content in diesel fuel — ULSD. The agency allowed for a phase-in period, but by 2014, all diesel fuel both on-road and off sold in the U.S. had transitioned to ULSD. This sulfur removal has opened the floodgates of microbial growth in diesel tanks because the natural sulfur biocide has been removed.

Formation of Solids in Storage

In Florida, during Hurricane Charlie in 2004, the Federal Emergency Management Agency (FEMA) reported that 50% of standby generators failed. At that time, most diesel fuel contained higher sulfur content in the range of 500 to 5,000 ppm, so in many cases microbes were likely not the main cause of these failures. Instead, these failures could be traced to diesel fuel instability.

As diesel fuel ages and is exposed to air, water, and other factors, its heavy-end asphaltene content will become unstable and start to drop out of the fuel. Some of these asphaltenes will be in suspension, while the rest will build up on the bottom of the storage tank, contributing to sludge. Asphaltenes in suspension can build up on the fuel filters and cause an engine failure or a reduction in revolutions per minute (RPMs). Since Florida had not seen very many direct strikes from major hurricanes since Hurricane Donna in 1960, there was a lot of old diesel fuel in the state’s emergency backup generators, much of it with high concentrations of solids developed over time.

After Hurricane Charlie and the subsequent active hurricane seasons of 2004 and 2005, sales of backup generators in Florida and the Gulf Coast increased dramatically. But most individuals purchasing these generators lacked the understanding of what they needed to do to maintain the stored fuel these generators would use. Many thought they just had to fill the tank with diesel fuel and that was it. However, most backup generators are only refueled once or twice a year, so fuel preventive maintenance (PM) is a must if you don’t want unpleasant surprises when you use the equipment.

Diesel fuel stored for long periods in a pump, such as the one pictured, may degrade or become contaminated. Photo: Shutterstock
Diesel fuel stored for long periods in a pump, such as the one pictured, may degrade or become contaminated. Photo: Shutterstock

Complacency Breeds Problems

For a number of years, I’ve said that I am expecting a higher failure rate on backup generators the next time Florida is hit with a major hurricane or emergency. People get complacent during these kinds of stretches. Then Hurricane Matthew hit Florida and the Southeast in October. At the time of this writing, we don’t know the results, but we will see the extent of the problem shortly. The fact that it had been 12 years since the last major hurricane strike means there is a lot of old diesel fuel with fuel-filter-plugging asphaltenes waiting to be used by emergency backup generators. In addition, because much of this fuel is now ULSD, there are untold numbers of fuel storage tanks out there with major proliferations of microbial growth due to the lack of microbe-inhibiting sulfur in the fuel.

Fungus and mold, along with the excretions coming from these little pests, are now the main cause of fuel-­related equipment problems. In our experience, fuel problems cause about 70% of all diesel engine failures, and microbial growth in fuel storage tanks contributes to 90% of those fuel problems. The importance of staying on top of this issue is clear.

Fuel pH Could Be a Problem Sign

A major part of this problem lies in the fact that the microbes living in diesel fuel excrete acids that damage the tank and fuel system over time. Low fuel pH is a sign of this problem. Remember that low pH means high acid. The normal pH for diesel fuel is between 5.5 and 8.0, so a reading of below 5.5 is an indicator there could be a problem. The industry recognizes that the lower the pH, the higher the potential for serious corrosive damage to metal components in the system. Some systems with serious corrosion problems have had fuel pH measured as low as 2.5.

There is no product on the market to raise the PH levels in diesel fuel. If you have low fuel pH, you have to address the source of the problem, which is usually microbes. Once these are under control, the fuel pH will eventually rise and stabilize through normal consumption and dilution that occurs when more fuel is added to the tank. In cases where fuel pH is extremely low, the other option is to dispose of the fuel. No viable chemical treatment will fix a low fuel pH problem.

Another aspect contributing to the problem is cross contamination, where ethanol fuel ends up in diesel tanks. This is caused by switch loading in transport tankers or tank vents with common piping. A truck hauling ethanol-blend fuel one day may be hauling diesel fuel the next. There can be small amounts of ethanol left in the bottom of the tanker truck that will mix into diesel fuel. When ethanol vapors cross over through the vent pipes into the diesel tanks, they will combine with any water in the bottom of the tank. Certain kinds of bacteria feed off the trace ethanol contamination and convert it to acidic acid. This acid is very destructive to tanks and fuel distribution systems.

The test strip on the left shows the presence of bacteria in diesel fuel, while the one on the right shows the presence of fungus and mold. Photo: Bell Performance
The test strip on the left shows the presence of bacteria in diesel fuel, while the one on the right shows the presence of fungus and mold. Photo: Bell Performance

The Importance of Removing Water

Fungus, mold, and bacteria need water to grow, so it is critical to deal with water content in storage tanks as soon as it is found. Many older diesel mechanics will tell you that water in diesel tanks below the fuel pick up is not a problem. Given the changes to diesel fuel that we mentioned before, today it’s a different story. The rule is zero water in a diesel tank. Microbes need water to grow — and keep in mind that a drop of water to a microbe is a lake.

Water can be detected by using a water-­finding paste that is placed on a stick and extended to the bottom of the tank. If the paste comes in contact with water, it will change colors. If water is detected, it needs to be pumped out. This can be a problem because most fuel distributors do not want to do it for their customers. It takes special licensing to handle, transport, and dispose of this petroleum-­contaminated water (PCW).

Another problem in removing the water is that most tanks are not level in the ground and if the opposite side of the tank from the filler port is lower, it is going to be almost impossible to pump it all out.

Chemicals available on the market can be used to bind with the remaining water to suspend it in the fuel, which would then be burned harmlessly in the engine. These should only be used with small amounts of water. The newer Tier 4 diesel engines should have less than 200 ppm of water content because some manufacturers will void the warranty on the engine if the fuel’s water content exceeds this.

Be Careful with Biodiesel

Another widespread change to the nation’s diesel fuel supply is the presence of low levels of biodiesel in most diesel fuels. Most diesel contains 2-5% biodiesel content, no matter where you get it from. In some ways, this is good (it solves ULSD’s lubricity problem), but it also contributes to a couple of the problems we mentioned before.

Microbes love to feed off biodiesel, so any biodiesel content can make microbe problems worse. Biodiesel is also, depending on the feedstock it’s made from, a lot less stable than diesel fuel, so any biodiesel content can contribute to fuel instability and solids formation. Finally, biodiesel can make cold-weather gelling problems worse, though this isn’t much of a problem until you reach 20% or greater biodiesel content in the diesel fuel.

Address the Problems Related to ULSD

The changes that have been made to diesel fuel, with the reduction of fuel sulfur to 15 ppm, require an ongoing comprehensive testing and fuel treatment program — a fuel PM program — in order to maintain reliable, problem-free fuel. 

Monitor the pH level in diesel tanks and ensure it is maintained above 5.5 (preferably in the 6.0 to 9.0 range) to prevent corrosive damage to fuel storage tanks, fuel system components, and dispensing equipment.
Keep storage tanks as full as possible at all times to prevent condensation. It only takes a seven-degree change in air temperature to cause water-vapor condensation on the internal bare walls of a storage tank. 
A key element of an effective fuel PM program is testing for water every 30 days at a minimum. Deal with water as soon as it is found either by pumping or using water-removing chemicals. Remember that water is your fuel’s main enemy because microbes need water to grow.

Diesel fuel stabilizer should be added in all diesel fuel that will be stored for long periods of time. Stabilizers slow the degradation of the fuel to protect its combustion quality for the longest time possible. In order for stabilizers to be fully effective, they need to be added when the fuel is fresh and in good shape. Add more stabilizer when fresh fuel is added.

If backup generators are only fueled a couple times a year, add biocide at a kill dose level, every time. Like stabilizers, biocides get “used up” over time, hence the need to re-treat the fuel periodically.

Most fleet managers have no idea what is happening to their stored fuel and the negative effects it could have on their backup generators, pumps, and stored fuel during emergencies. Most fleet managers also have no budget line item for fuel maintenance because they don’t know it’s necessary. Before the next emergency, fleet professionals should ensure their stored fuel is maintained and ready for use.

About the Author
James Dunst is the national training director for Bell Performance and is a specialist in fuel-related problems and solutions. He has 45 years of experience in the automotive and heavy-duty trucking industries.

COMMENTS

  1. 1. Danny O'Flaherty [ November 09, 2016 @ 11:36AM ]

    Great article with sound advice. We have started using a fuel polisher and a biocide in all our generators and I was very grateful they all worked when hurricane Matthew showed up.

 

Comment On This Story

Name:  
Email:  
Comment: (Maximum 10000 characters)  
Leave this field empty:
* Please note that every comment is moderated.

Recent Topics

I'm looking for fleet asset management software. We have 160 light duty vehicles. We have a lot of bells & whistles available through...

View Topic

We are looking for an accident protocol example that can be shared?

View Topic

Fleet Documents

907 Fleet Documents (and counting) to Download!

Fuel Saving Strategies Survey

View our 2008 survey to benchmark your fleet's fuel and green strategies with other fleets.
 

Fuel Calculator

A managed fuel program can help you save time and money and gain control over the way you fuel your vehicles. Determine your potential savings by using our fuel calculator.
Launch Fuel Calculator 

Fuel Prices

U.S. Gasoline and Diesel Fuel Prices.

Launch Fuel Prices 
Sponsored by

James Crocker is director of fleet operations, overseeing purchasing, remarketing, and logistics for Merchants Leasing.

Read more